Message

Message： hi,how much the cost of ucancam v9 ( professional version ) & the standard one. how can I buy it and the payment way.best regards . eng.husham 2013/02/17

Reply： Hello, I have sent the specific information to your email, pls check. ( 2013/02/17 )

Message： Good morning, i have a problem with save as .nc the file type.. in Toolpath output System Prompt Error in setting file path, please reset yesterday it worked, but today… i cant save as .nc the file type.. pls help ) Lomič 2013/01/23

Reply： Hello, pls reinstall the program and try! ( 2013/01/23 )

Message： Hi, I would like to upgrade to the Pro version of Ucancam Engraving Software. I am currently using Ucancam V8, Many Thanks Jamshid 2013/01/18

Reply： Hello, we will contact you by Email. ( 2013/01/18 )

Message： We came back from Holidays and started to setup the computers. The PC IN Question runs with XP Professional Somebody had removed the dongle UCANCAM V8 and when we connected everything including the dongle, it said it couldnt find the dongle. we tried reinstalling the software and when it come to the part that says installing dongle, it says it cant find the driver. Do you perhaps still have drivers for the V8 Dongles Dongle NO. M-9050249 Hope you can help Johnny 2013/01/17

Reply： Hello, pls download the install files(http://www.ucancam.com/V8.22-M-Eng.rar), after installation, open the directory which Ucancam exist in. and open the sub fold Drv, the dongleinstall.exe file is dongle driver. ( 2013/01/17 )

Message： On Win7, I did install version 8 in compatibility Win XP, 2000, NT4 and 98. And the installation of the “dongle key” with the same compatibility. But it does not work! How to operate Ucancam V8 with a Win7 PC? Jean Marc 2013/01/17

Reply： Hello, ucancam v8 can’t run in Windows 7, if you want to run ucancam in win7, you need buy or upgrade to ucancam V9. ( 2013/01/17 )

Message： Hi I am Shukhrat from Tashkent, I sent you a masssge a few days ago with my problem with software. Then you sent me Unfortunatly it not work. Please send me a software coincident with my dongle key. My Dongle Key is SN:M-7-0585. Anonymous 2013/01/16

Reply： Hello, pls give an Email address. ( 2013/01/16 )

Message： Hello, I changed my computer and I can not reinstall UcancamV8 with Windows 7. Message: “The dongle not found” (DOG USB KEY SN No. M-10050328) I would also passed a version 9, my USB is OK? Thank you for your answer Jean Marc 2013/01/16

Reply： Hello, ucancam V8 can’t run in windows7, you need run it in win2000 or winXP, V8 dongle can’t support version 9 program. ( 2013/01/16 )

Message： i have dongle SN:M-7-0585, i lost the software CD, can you please send me the link to download the appropriate software version. Shukhrat 2013/01/14

Reply： Hello, the link is http://www.ucancam.com/V8.22-M-Eng.rar ( 2013/01/14 )

Message： Hello!Tell me where to download the driver usb DogKey for windows 7. I use Ucancam V8 + Waveboard. In this program, I was happy with everything, but if it worked under windows 7, it would be perfect! Oleg 2013/01/11

Reply： Hello, your ucancam is v8, it can’t run in Windows 7, if you want to run ucancam in win7, you need buy or upgrade to ucancam V9. ( 2013/01/11 )

Message： Hello, I would like to upgrade to the Pro version of Ucancam Engraving Software. My Machine Jinka 361 Error -When turned on the screen is blank (“Normally Showing ” WELCOME “) Condition Knife As In Condition Cutting. -Third light (red, orange,green) Continuous Turns In. What is the solution? Is there a reset code it? Damami Sumalatan 2012/12/28

Reply： Hello，about the machine problem, pls contact the machine manufacturers ( 2012/12/28 )

GuestBook

Cancel reply